- Dd wrt v24 svn18946 wndr3400 install#
- Dd wrt v24 svn18946 wndr3400 driver#
- Dd wrt v24 svn18946 wndr3400 license#
Wl_module_init: rpcq_rxthresh set to 0x200 Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details. PCI: Setting latency timer of device 0000:00:01.0 to 64Įth1: Broadcom BCM4329 802.11 Wireless Controller 5.60.127.2706 usb_register_driver is being used by a non-GPL module, which will not be allowed in the future PCI: Setting latency timer of device 0000:00:02.0 to 64Įth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.127 wl_txq_thresh set to 0x200
Dd wrt v24 svn18946 wndr3400 license#
Warning: unable to open an initial console.Įmf: module license 'Proprietary' taints kernel. VFS: Mounted root (squashfs filesystem) readonly.
Dd wrt v24 svn18946 wndr3400 driver#
Usbcore: registered new interface driver usb-storageĦWIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API Usb 1-2: configuration #1 chosen from 1 choice Usb 1-2: new high speed USB device using ehci_hcd and address 2 Usb usb2: configuration #1 chosen from 1 choice Ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2 PCI: Setting latency timer of device 0000:00:04.0 to 64 Ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver Usb usb1: configuration #1 chosen from 1 choice Sflash: squash filesystem with lzma found at block 1505 Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled Squashfs: version 3.2-r2 (5) Phillip Lougher TCP: Hash tables configured (established 2048 bind 2048) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Time: MIPS clocksource has been installed. Usbcore: registered new device driver usb Usbcore: registered new interface driver hub Usbcore: registered new interface driver usbfs Memory: 61168k/65532k available (2779k kernel code, 4300k reserved, 556k data, 184k init, 0k highmem)Ĭalibrating delay loop. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) PID hash table entries: 256 (order: 8, 1024 bytes)ĭentry cache hash table entries: 8192 (order: 3, 32768 bytes) Synthesized TLB modify handler fastpath (31 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB refill handler (20 instructions). Primary data cache 32kB, 4-way, linesize 32 bytes. Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit VmallocChunk: 782516 kB Boot from /proc/kmsg System type : Broadcom BCM5357 chip rev 2 Root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit With any luck, you will see the OpenWrt login page.īusyBox v1.7.2 ( 18:15:36 CST) built-in shell (ash)Įnter 'help' for a list of built-in commands. Please don't turn off the power…” Then you will see the message “Rebooting the router now, please wait.” You will see the status bar fill up, then you can browse back to 192.168.1.1. You should see the message “Note: It will take about 1.5 minutes for firmware upgrade. Select the OpenWrt image from your computer (ex: openwrt-18.06.2-brcm47xx-mips74k-netgear-wndr3400-v3-squashfs.chk), then select Upload and confirm. Select the Advanced tab, then Administration, then Router Update. Login with default credentials admin:password Do you want Netgear Genie to help?” select “No, I want to configure the Internet connection myself.” Click next, then confirm. If you get a message that says “You are not connected to the Internet. Navigate to this address in a browser and you will see the Netgear Genie Wizard. Make sure your computer has an IP address in the 192.168.1.2-254 range. Release the reset button and the device will restart.Ĭonnect your computer to one of the LAN ports on the router. With the power on, press and hold the reset button for about 8 seconds until the power light begins to blink slowly.
Dd wrt v24 svn18946 wndr3400 install#
→ Install OpenWrt (generic explanation) Installation v1įirst, do a factory reset of the device.